ProductPRODUCTS
contact us
PH：+86 180 3717 4417(Ms.Van)
Tel：+86 0371-5608 1253
Mail：daqinjixie@qq.com
Add：High-tech Development Zone, Zhengzhou City, Henan Province，China
Briquetting machine hydraulics
add time：2015-12-08
The hydraulic device is a hydraulic power source composed of a motor, a hydraulic pump, a valve, a fuel tank, and the like.
The fuselage adopts the welding structure. The inner wall of the fuselage adopts the quenching material Q235 liner, hardness HRc38-42, can be replaced after wear. The inner walls of all hydraulic cylinders must be rolled and hardened, and the rods are quenched and plated.
Hydraulic systems include power units, fuel tanks, hydraulic valves, hydraulic lines, and accessories. The hydraulic pump adopts Qidong High-Pressure Oil Pump Plant; the electro-hydraulic reversing valve adopts Jiangyin Dehong products; the seal ring adopts Ningbo Ilka sealing products; the motor adopts domestically-produced Nanjing Global Motors; and other accessories are produced by well-known domestic manufacturers.
Electrical systems include electrical control cabinets, operator stations, limit switches, and control circuits.
The material to be packed is added into the material box, the handle of the reversing valve is operated, the door cover is closed and the lock head locks the door cover so as not to float, and the primary preloading is performed, and then the pressure measuring cylinder advances to carry out secondary compression; the stroke is in place, The main pressure cylinder advances to the final compression, and after the main pressure cylinder reaches the system pressure, the pressure is maintained for 3-5 seconds. The main and side pressure cylinders return, pull out the lock and open the cover, turn over the oil cylinder to work out the mass and return. A work cycle is completed at this time.
(Note: The length of the bundle depends on the weight, material and geometry of the material being squeezed. Therefore, it is not allowed to put too much material on the material that is relatively thick, that is, it has a higher density. Otherwise, the length of the bundle will be too long. Can not launch mass, or even cause side pressure head can not be in place, leading to a series of drawbacks such as misalignment of the main head.)
The fuselage adopts the welding structure. The inner wall of the fuselage adopts the quenching material Q235 liner, hardness HRc38-42, can be replaced after wear. The inner walls of all hydraulic cylinders must be rolled and hardened, and the rods are quenched and plated.
Hydraulic systems include power units, fuel tanks, hydraulic valves, hydraulic lines, and accessories. The hydraulic pump adopts Qidong High-Pressure Oil Pump Plant; the electro-hydraulic reversing valve adopts Jiangyin Dehong products; the seal ring adopts Ningbo Ilka sealing products; the motor adopts domestically-produced Nanjing Global Motors; and other accessories are produced by well-known domestic manufacturers.
Electrical systems include electrical control cabinets, operator stations, limit switches, and control circuits.
The material to be packed is added into the material box, the handle of the reversing valve is operated, the door cover is closed and the lock head locks the door cover so as not to float, and the primary preloading is performed, and then the pressure measuring cylinder advances to carry out secondary compression; the stroke is in place, The main pressure cylinder advances to the final compression, and after the main pressure cylinder reaches the system pressure, the pressure is maintained for 3-5 seconds. The main and side pressure cylinders return, pull out the lock and open the cover, turn over the oil cylinder to work out the mass and return. A work cycle is completed at this time.
(Note: The length of the bundle depends on the weight, material and geometry of the material being squeezed. Therefore, it is not allowed to put too much material on the material that is relatively thick, that is, it has a higher density. Otherwise, the length of the bundle will be too long. Can not launch mass, or even cause side pressure head can not be in place, leading to a series of drawbacks such as misalignment of the main head.)
